电压对电刷镀三价铬镀层性能的影响

在45钢表面电刷镀得到三价铬镀层,镀液组成和工艺条件为:Cr2(SO4)36H2O 0.4 mol/L,甲酸铵0.5 mol/L,氨基乙酸0.5 mol/L,H3BO30.6 mol/L,NaH2PO2 H2O 0.3 mol/L,pH=1.5,温度50°C,镀笔移动速率15 cm/s。研究了电压对镀铬层显微结构、表面粗糙度、厚度、显微硬度和耐磨性的影响。随电压增大,镀层厚度增大,显微硬度和耐磨性均先提高后降低。电压为14 V时,镀层的表面平整,粗糙度为2.387μm,显微硬度为602 HV,耐磨性最好。     

SiC nanoparticles incorporation in electroless NiP-Graphene oxide nanocomposite coatings

The presence of SiC nanoparticles within the Graphene oxide (GO) incorporated electroless deposited NiP layers (NiP-GO) on carbon steel substrate was studied in this work. The effect of co-deposition of GO nanoplatelets and/or SiC nanoparticles on the morphology and structure of the heat-treated NiP coatings were investigated by scanning electron microscope and X-ray diffraction, respectively. The results revealed that the heat-treated NiP and NiP–SiC coatings consisted of Ni and Ni₃P phases, whereas the NiP-GO also contains the intermediated Ni₂P and Ni₁₂P₅ metastable phases due to the incomplete precipitation of Ni₃P. Such metastable phases are significantly decreased by the incorporation of SiC nanoparticles in NiP-GO coatings. The mechanical properties of the coatings were characterized by microhardness measurement and “pin on disk” wear test. The corrosion tests were conducted in aqueous 3.5 %wt NaCl using electrochemical measurement for Ni–P, NiP-GO, NiP–SiC, and NiP-GO-xSiC coatings. By co-deposition of SiC nanoparticles, the hardness of NiP-GO is significantly increased and the wear loss is reduced, especially at a high sliding distance during the wear test. The corrosion behavior of the NiP-GO coatings containing different amounts of SiC nanoparticles has been investigated.     

Pure CuBi2O4 Photoelectrodes with Increased Stability by Rapid Thermal Processing of Bi2O3/CuO Grown by Pulsed Laser Deposition

A new method for enhancing the charge separation and photo‐electrochemical stability of CuBi₂O₄ photoelectrodes by sequentially depositing Bi₂O₃ and CuO layers on fluorine‐doped tin oxide substrates with pulsed laser deposition (PLD), followed by rapid thermal processing (RTP), resulting in phase‐pure, highly crystalline films after 10 min at 650 °C, is reported. Conventional furnace annealing of similar films for 72 h at 500 °C do not result in phase‐pure CuBi₂O₄. The combined PLD and RTP approach allow excellent control of the Bi:Cu stoichiometry and results in photoelectrodes with superior electronic properties compared to photoelectrodes fabricated through spray pyrolysis. The low photocurrents of the CuBi₂O₄ photocathodes fabricated through PLD/RTP in this study are primarily attributed to their low specific surface area, lack of CuO impurities, and limited, slow charge transport in the undoped films. Bare (without protection layers) CuBi₂O₄ photoelectrodes made with PLD/RTP shows a photocurrent decrease of only 26% after 5 h, which represents the highest stability reported to date for this material. The PLD/RTP fabrication approach offers new possibilities of fabricating complex metal oxides photoelectrodes with a high degree of crystallinity and good electronic properties at higher temperatures than the thermal stability of glass‐based transparent conductive substrates would allow.     

高硬度环保耐蚀柴油机气缸套的研制

在缸套表面进行镍磷复合镀强化处理,可以提高湿式内燃机缸套耐腐蚀性能,但会增加产品的成本。研究了在普通贝氏体气缸套材料基础上去掉贵重金属镍,调整其他成分比例,在确保材料性能不变的前提下,降低产品的成本。结果表明,配合表面强化处理,缸套硬度高、耐腐蚀强、生产成本低,并可以延长发动机寿命。     

电弧离子镀NiAlHf涂层的抗高温氧化性能

目的通过电弧离子镀技术,获得抗氧化性能优良的NiAl涂层。方法采用电弧离子镀技术,在弧流为110 A,偏压为-50 V的参数下沉积NiAlHf涂层。通过X射线衍射仪(XRD)和扫描电子显微镜(SEM)对涂层的物相结构和形貌进行分析,通过能谱仪(EDS)分析涂层的成分。采用恒温氧化增重实验对涂层的氧化动力学进行分析。结果由电弧离子镀技术制备的NiAl涂层致密均匀,无大颗粒、孔洞等缺陷。涂层主要由β-NiAl相组成,活性元素Hf固溶在主相中。NiAlHf涂层表现出良好的抗高温氧化性能,动力学曲线符合抛物线规律,在1150℃下恒温氧化200h的平均氧化速率为0.0841g/(m^2×h),远优于传统MCrAlY涂层体系。NiAlHf涂层在氧化初期形成保护性的α-Al2O3氧化皮以及少量亚稳态的θ-Al2O3,随后θ-Al2O3逐渐转变为稳态的α-Al2O3。Hf在涂层表面富集从而形成HfO2,对氧化皮形成了钉扎作用,增强了氧化皮的粘附性,提高了涂层的抗氧化性能。随着氧化的进行,涂层中的β-NiAl相逐渐转变为γ'-Ni3Al相。结论 NiAlHf涂层在1150℃下仍具备优良的抗高温氧化性能,对下一代耐更高温度涂层开发,电弧离子镀NiAl涂层的技术推广及工业化应用有一定的指导作用。     

现代镀覆技术 第二部分──化学镀镍(续4)

给出了各种实用的化学镀镍配方及其工艺条件。     

Co-Cu-Zn三元系相平衡的实验研究

本实验通过采用电子探针显微分析和X-ray衍射分析方法实验研究了Co-Cu-Zn三元体系在800°C和1000°C时的相平衡。在这两个等温截面中均未发现三元化合物。在800°C等温截面，Co在β-CuZn相中的固溶度为32.36%，Cu在β1-CoZn相中的固溶度为5.28%。除此之外，γ-Co5Zn21和γ-Cu5Zn8具有相同的晶体结构，因此，它们之间形成了一个贯穿连续固溶体相。1000°C的等温截面中，β-CuZn相、β1-CoZn相、γ-Co5Zn21相、γ-Cu5Zn8相都消失了。随着温度从800°C上升到1000°C，液相区域增大。     

Nanoindentation and scratch behaviour of Ni–P electroless coatings

ABSTRACT

In the present paper, the mechanical properties and the scratch failure mechanisms of Ni–P electroless coatings are described. The material microstructure was studied in as-deposited and annealed conditions through SEM and EDS analyses. Nanoindentation measurements on the coatings showed a remarkable hardening due to the crystallization and precipitation behaviour produced by annealing. The scratch tests, conducted by increasing the load during scratch, revealed the coating failure mechanisms in a broad range of applied stresses up to delamination.     

基底表面质量对ZK60镁合金镀镍层性能的影响

镁合金表面镀镍被广泛运用于镁合金工件防腐,而镀层的起泡和脱落严重影响工件的使用寿命。本实验以ZK60镁合金为研究对象,分析了不同工件基底表面质量对镀镍层性能的影响机制。研究表明:基底表面存在的划痕和点蚀坑会显著降低镀镍层质量,引起镀层的起泡和脱落。基底表面的划痕会被保留到镀镍层中,引发镀层变薄,应力集中等问题,增加镀层开裂的几率。点蚀坑中的杂质与镁基底有不同的电化学特性,会导致镀层减薄和结合不牢。因此,提高镁合金工件基底表面光洁度、清除基底表面点蚀坑是提高镁合金镀镍层性能的必要措施。